StarTechcom Car Video System ST12MHDLAN User Manual

HDMI® Audio/Video Over IP Extender Kit  
ST12MHDLAN  
*actual product may vary from photos  
DE: Bedienungsanleitung - de.startech.com  
FR: Guide de l'utilisateur - fr.startech.com  
ES: Guía del usuario - es.startech.com  
IT: Guida per l'uso - it.startech.com  
NL: Gebruiksaanwijzing - nl.startech.com  
PT: Guia do usuário - pt.startech.com  
Manual Revision: 03/15/2013  
 
Table of Contents  
Introduction............................................................................................1  
Packaging Contents ................................................................................................................................. 1  
System Requirements.............................................................................................................................. 1  
Preparing Your Site ................................................................................................................................... 3  
Hardware Installation Using Gigabit LAN Network ...................................................................... 4  
Hardware Reset Procedure .................................................................................................................... 6  
EDID Copy.................................................................................................................................................... 6  
Factory Default Setting........................................................................................................................... 6  
Specifications..........................................................................................7  
Technical Support ..................................................................................8  
Warranty Information............................................................................8  
Instruction Manual  
i
 
Introduction  
The ST12MHDLAN HDMI® Over IP Extender kit lets you extend an HDMI® audio and  
video signal over a Gigabit LAN network. The kit includes both the extender and  
receiver for a complete all-in-one solution, and offers a highly scalable installation  
when used with additional ST12MHDLANRX receiver units (sold separately). The  
ST12MHDLANRX receivers can be connected to the same network to output the HDMI®  
signal to over 100 additional displays.  
This flexible HDMI® extender can be connected through a Gigabit LAN portal and span  
the entire distance of your network, or connected point-to-point with no network  
hub for a small scale one-to-one extension of up to 330 feet (100 meters). Plus,  
because the HDMI® signal is extended over standard Cat5e/Cat6 Ethernet cable with  
RJ45 connectors, proprietary cables aren’t necessary, eliminating both the expense  
and hassle of running specialized cables. For added versatility, up to 16 different  
ST12MHDLAN Transmitter units can be added to a single network (IGMP Network  
support required).  
The HDMI® over IP Extender kit includes optional mounting hardware for a professional  
and tidy installation.  
Ideal for High-Definition applications, the extender supports 1080p video resolutions,  
digital stereo audio, and features built-in EDID monitor emulation, which ensures  
native resolution and maximum compatibility with your display or projector, for a  
convenient plug-and-play installation.  
Backed by a StarTech.com 2-year warranty and free lifetime technical support.  
Packaging Contents  
1 x HDMI® over IP Transmitter Unit  
1 x HDMI® over IP Receiver Unit  
2 x Mounting Bracket Kit  
2 x Foot Pad Set  
2 x Power Adapters  
1 x Instruction Manual  
System Requirements  
HDMI® enabled video source (i.e. computer, Blu-ray Player)  
HDMI® enabled display device(s) One for each Receiver (i.e. television, projector)  
Available AC electrical outlet for the Transmitter, and each Receiver  
HDMI® cable for each display  
Gigabit Networking devices and cabling  
Instruction Manual  
1
 
Transmitter Unit  
6
2
2
3
1
1
3
4
5
1. F2 (Not Active)  
1. Power Jack  
2. F1 (Used during factory  
default setting)  
2. Network Status LED  
3. Reset Button  
3. Dip Rotary Switch (Used to  
pair Transmitter to Receiver)  
4. LAN Port (RJ-45 Connector)  
5. Video In  
6. Link OK POWER LED  
Receiver Unit  
(Additional Receiver units sold seperately ST12MHDLANRX)  
6
2
2
3
1
1
3
4
5
1. F2 (Used during EDID Copy  
procedure)  
1. Power Jack  
2. Network Status LED  
3. Reset Button  
2. F1 (Used during factory  
default setting)  
4. LAN Port (RJ-45 Connector)  
5. Video Out  
3. Dip Rotary Switch (Used to  
pair Transmitter to Receiver)  
6. Link OK POWER LED  
NOTE: Serial 1 (Control) Ports, and Serial 2 (AUX/EXT) Ports are not active  
Instruction Manual  
2
 
Preparing Your Site  
NOTE: The ST12MHDLAN HDMI® extender kit can use a Gigabit LAN Network to  
extend the signal. Most Gigabit Network portals have a cable length restriction of  
330 ft. (100m). Refer to the manufacturer of the equipment to determine the length  
restriction and ensure the Transmitter Unit, and Receiver Unit(s) are all within the  
restricted range of the nearest network portal.  
Ensure the Transmitter Unit, and Receiver Unit(s) are all situated near an available AC  
electrical outlet.  
1. Determine where the local video source (i.e. computer, Blu-ray Player) will be  
located and set up the device.  
2. Determine where the remote display will be located and place/ mount the  
display appropriately.  
3. (Optional) If using additional receiver units (ST12MHDLANRX sold separately),  
determine where the remote displays will be located in and place/ mount the  
displays appropriately.  
Instruction Manual  
3
 
Hardware Installation Using Gigabit LAN Network  
1. Install Transmitter Unit  
a) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player).  
b) Connect an HDMI cable from the video source device (i.e. computer, Blu-ray  
Player) to the “Video Inport on the Transmitter Unit.  
c) Connect the provided Transmitter Unit power supply.  
2. Install Receiver Unit(s)  
a) Position the Receiver Unit(s) near the video display (i.e. television, projector).  
b) Connect an HDMI cable from the display Input to the “Video Outport on the  
Receiver Unit.  
c) Connect the provided Receiver Unit power supply.  
d) (optional) If using additional ST12MHDLANRX Receivers (sold separately), repeat  
steps for each additional Receiver.  
NOTE: The “Dip Rotary Switchon the Extender and each Receiver connected to the  
network must be set in the same position for the devices to communicate.  
3. Connect the devices to a Gigabit LAN Network  
a) Connect an RJ-45 terminated Cat5e/6 Ethernet cable to the “LAN Port(RJ-45  
Connector) on the Transmitter unit, and all receiver units.  
NOTE: If you are using surface cabling, ensure you have enough Category 5e/6  
unshielded twisted pair (UTP) network cabling to connect the Transmitter Unit to the  
Gigabit LAN hub, router, or switch.  
OR  
If you are using premises cabling, ensure that the Category 5e/6 unshielded twisted  
pair (UTP) network cabling between the Transmitter and Gigabit LAN hub, router, or  
switch has been properly terminated in a wall outlet in each location and there is a  
patch cable long enough to connect the Network portal and Transmitter Unit to their  
respective outlets.  
b) Connect the other end of the Cat5e/6 cable run to a Gigabit LAN hub, router  
or switch.  
c) (optional) When adding additional Receiver Units (ST12MHDLANRX – Sold  
separately), a run of Cat 5e/6 cable will be required from each device to the Gigabit  
LAN hub, router or switch.  
4. Your source video image will now appear on the Receiver unit(s) attached  
video display.  
Instruction Manual  
4
 
(Optional) Point to Point Hardware Installation without Gigabit LAN Network  
NOTE: While range is reduced to a maximum of 330 feet (100 Meters) the  
ST12MHDLAN HDMI® extender kit also allows for extending the signal without a  
Gigabit LAN Network by connecting the Transmitter directly to the Receiver using  
CAT5e/6 cabling. This also eliminates the ability to add additional Receivers.  
1. Install Transmitter Unit  
d) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player).  
e) Connect an HDMI® cable from the video source device (i.e. computer, Blu-ray  
Player) to the “HDMI INon the Transmitter Unit.  
f) Connect the provided Transmitter Unit power supply.  
2. Install Receiver Unit(s)  
e) Position the Receiver Unit(s) near the video display (i.e. television, projector).  
f) Connect an HDMI® cable from the display Input to the “Video Outport on the  
Receiver Unit.  
g) Connect the provided Receiver Unit power supply.  
NOTE: The “Dip Rotary Switchon the Extender and Receiver connected must be set in  
the same position for the devices to communicate.  
3. Install RJ-45 terminated Cat5e/6 Ethernet Cable  
d) Connect an RJ-45 terminated Cat5e/6 Ethernet cable to the HDMI® Out Link  
(RJ-45 Connector) on the Transmitter unit.  
NOTE:  
If you are using surface cabling, ensure you have enough Category 5e/6 unshielded  
twisted pair (UTP) network cabling to connect the Transmitter Unit to the Receiver  
Unit’s location, and that each end is terminated with a RJ45 connector.  
OR  
If you are using premises cabling, ensure that the Category 5e/6 unshielded twisted  
pair (UTP) network cabling between the Transmitter and Receiver Units have been  
properly terminated in a wall outlet in each location and there is a patch cable long  
enough to connect the Remote Unit and the Host Unit to their respective outlets.  
e) Connect the other end of the Cat5/6 cable run to the RJ45 connector on the  
remote Unit Receiver Unit.  
4. Your source video image will now appear on the remote unit(s) attached  
video display.  
Instruction Manual  
5
 
Hardware Reset Procedure  
NOTE: If video signal does not appear on the display a hardware reset can be  
performed on the Transmitter Unit, or individual Receiver Units.  
1. Press the reset button on the device using a pin point tool, such as a ballpoint pen  
or a bent paper clip.  
EDID Copy  
EDID allows the video source to output the most ideal signal to the video display. The  
“EDID Copyfunction on the ST12MHDLANRX ensures that EDID is still active through  
the Ethernet extender.  
NOTE: If you using multiple receivers the EDID can only be copied from one unit, the  
signal customized for that display will be applied to all displays connected through  
additional receivers.  
1. Disconnect the power cable from the Receiver.  
2. Hold down the F2 button  
3. Reconnect the Power while holding down the F2 button  
4. Release F2 button after the power has been reconnected for 12 seconds (the  
Network Status LED flashes yellow), EDID is now active through the  
Ethernet extender.  
Factory Default Setting  
1. Disconnect the power cable from the Transmitter/Receiver.  
2. Hold down the F1 button  
3. Reconnect the Power while holding down the F1 button  
4. Release F1 button after the power has been reconnected for 17 seconds (the Link  
OK POWER LED flashes green and blue)  
5. Reconnect the Power again.  
Instruction Manual  
6
 
Specifications  
Maximum Digital Resolutions  
Supported Resolutions  
Wide Screen Supported  
Audio Specifications  
Interface  
1920x1200 @60Hz  
1920 x 1200 (1080p)  
Yes  
Stereo Sound  
HDMI®  
Cabling  
Cat 5e UTP or better  
Yes  
Audio  
Rack-Mountable  
Yes  
HDMI®  
HDCP  
Industry Standards  
Daisy-Chain  
Yes  
1x HDMI® (19 pin)  
1x RJ-45  
Transmitter Connectors  
1x HDMI® (19 pin)  
1x RJ-45  
Receiver Connectors  
Power Adapter Input Voltage  
Power Adapter Input Current  
Power Adapter Output Voltage  
Power Adapter Output Current  
Center Tip Polarity  
100~240V  
0.4 A  
5 DC V  
2 A  
Positive  
M
Plug Type  
Instruction Manual  
7
 
Technical Support  
StarTech.com’s lifetime technical support is an integral part of our commitment to  
provide industry-leading solutions. If you ever need help with your product, visit  
www.startech.com/support and access our comprehensive selection of online tools,  
documentation, and downloads.  
For the latest drivers/software, please visit www.startech.com/downloads  
Warranty Information  
This product is backed by a two year warranty.  
In addition, StarTech.com warrants its products against defects in materials  
and workmanship for the periods noted, following the initial date of purchase.  
During this period, the products may be returned for repair, or replacement with  
equivalent products at our discretion. The warranty covers parts and labor costs only.  
StarTech.com does not warrant its products from defects or damages arising from  
misuse, abuse, alteration, or normal wear and tear.  
Limitation of Liability  
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their  
officers, directors, employees or agents) for any damages (whether direct or indirect,  
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,  
or any pecuniary loss, arising out of or related to the use of the product exceed the  
actual price paid for the product. Some states do not allow the exclusion or limitation  
of incidental or consequential damages. If such laws apply, the limitations or exclusions  
contained in this statement may not apply to you.  
Instruction Manual  
8
 
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.  
StarTech.com is your one-stop source for every connectivity part you need. From  
the latest technology to legacy products — and all the parts that bridge the old and  
new — we can help you find the parts that connect your solutions.  
We make it easy to locate the parts, and we quickly deliver them wherever they need  
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to  
the products you need in no time.  
to access exclusive resources and time-saving tools.  
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology  
parts. StarTech.com was founded in 1985 and has operations in the United States,  
Canada, the United Kingdom and Taiwan servicing a worldwide market.  
 

Sennheiser Home Security System HD 25 User Manual
Sharp Microwave Oven R 8000G User Manual
Silvercrest Food Processor SMZ 260 B1 User Manual
Snapper Lawn Mower 1690043 User Manual
Snapper Yard Vacuum SV25500HV ESV25550HV SV25550HC SV25650B User Manual
Sony Universal Remote RM PP505L User Manual
Speco Technologies Security Camera HT 7247IHR User Manual
Stiga Snow Blower 8218 2220 70 User Manual
Summer Infant Safety Gate 7064 User Manual
Sylvania CRT Television C6427FE User Manual