Stanton Music Mixer SK ONE User Manual

FADER CLEANING  
The SK ONE faders may need lubrication from time to time. This will extend the  
fader life and eliminate any potential damage due to extended heavy usage.  
S K O N E Professional performance mixer  
Cleaning Instructions  
cable coming from the mixer.  
1. Remove the 3 fader knobs and 4 screws  
located in the corners of the PROTEKT™  
3. Spray a small amount of cleaner or  
lubricant into both ends of the fader and  
slide the fader back and forth a few times  
to spread the fluid evenly throughout the  
fader.  
(see “  
” inside) panel  
and take the panel off the mixer.  
2 . Remove the fader to be cleaned by  
unscrewing the 2 outer screws (removing  
the 2 inner screws will detach the fader  
from the fader plate) and disconnect the  
4. Shake and wipe off excess fluid before  
re-assembling the fader.  
REPL ACEMENT PARTS  
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning  
instructions. The following replacement parts are available from Stanton or your  
local Stanton dealer.  
PL-SK1  
Two way input toggle switch  
PP-SK1  
PROTEKT™ panel  
3PL-SK1 Three way input toggle  
switch with FLASH™  
PS-13US US Power Supply (110v)  
LF-SK1  
CF-SK1  
Channel input fader  
Crossfader  
PS-13EU European Power Supply (220v)  
PS-13UK UK only Power Supply (240v)  
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES  
REPLACING INSTRUCTIONS  
ROTATING INSTRUCTIONS  
1. Remove the PROTEKT™ panel  
1 . Remove the PROTEKT™ panel  
O W N E R ’S M A N U A L  
2. Remove the 2 outer screws from the tog-  
gle switch plate (removing the 2 inner  
screws will detach the switch from the  
plate)  
2. Remove the 2 outer screws from the tog-  
gle switch plate (removing the 2 inner  
screws will detach the switch from the  
plate)  
3. Remove the switch assembly and dis-  
connect the cable coming from the mixer.  
3. Rotate the plate to the desired position  
and tighten the screws back in the top and  
bottom holes  
4. Set the replacement switch assembly in  
the desired position and place the screws  
back in the top and bottom holes.  
S TANTON M AGNETICS , LLC  
2 8 2 1 Evans St. Hollywood, FL 3 3 0 2 0  
(9 5 4 ) 9 2 9 -8 9 9 9 - Fax: (9 5 4 ) 9 2 9 -0 3 3 3  
info@stantonmagnetics.com  
© 1999, Stanton Magnetics, LLC  
 
DESCRIPTION OF FUNCTIONS  
normal (20dB), or long (30dB) fade.  
8. Channel fader: Controls the input channel level.  
9. Crossfader: Fades the master output between channels 1 and 2.  
10. Master level control: Controls the overall signal output level.  
11. Crossfader Curve adjustment: Adjusts the shape of the crossfader curve from a quick cut  
for scratching and cutting to a longer fade for mixing.  
12. Crossfader Reverse: Reverses the direction of the crossfader. Bi-color LED indicates the  
status of the crossfader reverse function. When LED is green, the crossfader is normal.  
When LED is red, the crossfader direction is reversed.  
13. Headphone level control: Controls the overall headphone output level. It is recommend-  
ed headphones with an impedance rating of 200 ohms or less be used for maximum vol-  
ume.  
14. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing the  
user to preview a mix.  
1. Gain control: Controls the input sensitivity of each channel.  
2. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB)  
Any changes made to EQ settings will change the overall output level.  
3. Pan control: Controls left/right output balance of each channel.  
4. Input Fader Reverse: Reverses the direction of each respective input channel fader.  
Includes bi-color LED to indicate the status of the reverse function. When LED is green,  
the fader is normal. When LED is red, the fader direction is reversed.  
5. Input Level Meter: Monitors each channel’s input level.  
6. Input selector switches: Selects phono or line inputs.  
7. Input Fader Curve Adjustment: Adjusts the curve of the input faders between quick (6dB),  
 
FU N C TI O NS (contd)  
TECHNIC AL SPECIFIC ATIONS  
Line inputs:  
Phono inputs:  
Master output:  
2 (RCA), 150 mV / 27K ohm  
2 (RCA), 3 mV / 47K ohm  
1 (1/4” TRS Balanced/RCA unbalanced),  
775 mV / 1K ohm  
15. Headphone output: Connection for 1/4 inch headphone. Recommended headphone  
impedance is 32-200 ohms for maximum volume.  
Record output:  
Headphone output:  
Frequency Response:  
Tone Control :  
Gain Control:  
S/N Ratio:  
T.H.D:  
Dimension(LxWxD):  
Weight:  
1 (RCA), 245 mV / 10K ohm  
1 (1/4 inch), 32 - 200 ohms recommended  
20 Hz - 20 kHz, +/- 2 dB  
+ 9/-26 dB (Hi, Low)  
0-20dB  
Less than 70dB  
less than 0.2%  
13 6/8” x 7 2/8x 4” ( 350 x 184 x 102 mm)  
7 lbs (3.2 Kg)  
16. Master output: TRS balanced (1/4”).  
17. Power switch: Selects power "ON" or "OFF".  
18. Power supply connector: Input connection for the accompanying power supply.  
19. Ground connector: Connects to the turntable ground connector to eliminate electrical  
hum. Ground connectors usually supplied with turntables.  
20. Channel inputs: Line and phono signal inputs. Line inputs are used to connect to  
line level sources such as CD players, samplers, tape players, etc. Phono  
inputs are used to connect to turntables. Master output connects to an ampli-  
fier, EQ, crossover, or other outboard signal processing. Record out connects  
to tape recorder, mini disk recorder, etc.  
21. Outputs: Rec and unbalanced master outputs.  
WARRANT Y  
SPECIAL PROTE K TI O N  
This unit has been designed and manufactured using quality  
components. Therefore, it is warranted to be free from defects in materi-  
als (limited as specified below), and workmanship for a period of twelve  
(12) months from the original purchase date. During this period, all  
service and parts necessary to repair a defect will be free of charge. This  
limited warranty applies to mechanical parts which are subject to wear  
and tear as specified:  
Your SK ONE comes with a special PROTEKT™ aluminum panel designed to  
make the surface of the mixer is as smooth as possible while still enabling you  
to field-replace key components. The PROTEKT™ panel covers all screws that  
may get in the way of your performance. You can still easily remove the front  
panel to replace any of the modular parts which are subject to wear and tear:  
crossfader, input faders and input toggle switches.  
• Faders, specified durability: 15,000 cycles  
• Rotary potentiometers, specified durability: 10,000 cycles  
• Switches, specified durability: 10,000 cycles  
Consequently, the parts listed above are warranted to be free from  
defects in materials and workmanship for a period of thirty days (30)  
days from the original purchase date.  
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE  
ONLINE WARRANTY REGISTRATION FORM FOUND AT  
WWW.STANTONMAGNETICS.COM  
2821 Evans Street • Hollywood, FL 33020  
 

Sharp Computer Monitor LL T1610W User Manual
Silvercrest Blender SSM 550 A16 User Manual
SonicWALL Security Camera Email Security 70 8000 User Manual
Sony Car Stereo System CDX R3300 User Manual
Sony Personal Computer VPCS13 User Manual
Speed Queen Clothes Dryer BE 3113 User Manual
Stanley Black Decker Food Processor HG80 User Manual
Star Trac Exercise Bike S RB RECUMBENT BIKE User Manual
Sunbeam Water Dispenser WF5700 User Manual
Tanaka Brush Cutter TBC 4501 User Manual