Speco Technologies Security Camera WDR R3 User Manual

Wide Dynamic Range  
Dome Camera  
WDR-D3  
200 New Highway  
Amityville, NY 11701  
631-957-8700  
Please read this manual thoroughly before operation and keep  
it handy for further reference.  
 
WARNING & CAUTION  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION  
:
TO REDUCE THE RISK OF ELECTRIC SHOCK  
D O N O T R E M O V E C O V E R ( O R B A C K ) .  
NO USER SER VICEABLE PART S INSIDE  
R E F E R S E R V I C I N G T O Q U A L I F I E D  
S E R V I CE PER SONNEL._______________  
The lighting flash with an arrowhead symbol, within an equilateral triangle is  
Intended to alert the user to the presence of un-insulated “dangerous voltage”  
within the product’s enclosure that may be of sufficient magnitude to constitute  
a risk of electric shock to persons____________________________________  
The exclamation point within an equilateral triangle is intended to alert the user  
to the presence of important operating and maintenance (serving) instructions  
in the literature accompanying the appliance__________________  
INFORMATION -This equipment has been tested and found to company with  
l i m i t s f o r  
These limits are designed to provide reasonable protection against harmful  
I nterference W hen the equipments operated in commercial environment.  
a
c l a s s  
a
d i g i t a l device Pursuant to part 15 of the FCC rules.  
a
This equipment generates, uses, and Can Radiate radio frequency energy and  
if not installed and used in accordance with the instruction manual, may Cause  
Harmful interference to radio communications. Operation of this equipment in  
a
r e s i d e n t i a l a r e a i s l i k e l y t o c a u s e h a r m f u l i n t e r f e r e n c e i n w h i c h  
Case the user will be required to correct the interference at his own expense.  
WARNING – Change or modification not expressly approved by the manufacturer could void  
the user’s authority to operate the equipment__________________________________  
CAUTION : To prevent electric shock and risk of fire hazards.  
DO NOT use power sources other than that specified.______  
DO NOT expose this appliance to rain or moisture.000  
This installation should be made by a qualified service person and should conform to all local codes.  
 
CAMERA INSTALLATION  
CONNECT POWER CABLE  
1. WHEN USING 12 VOLTS DC (constant voltage 600 mA)  
POWER INPUT:RED  
CONNECT  
CENTER:(+)  
POWER SUPPLY  
2. WHEN USING 24 VOLTS AC (40 Volt Amps)  
POWER  
RED(+)  
CONNECT  
BLACK:(-)  
POWER SUPPLY  
3. CONNECT VIDEO CABLE  
-CONNECT BNC CABLE TO THE BNC JACK.  
YELLOW:VIDEO OUT  
 
CHAMELEON DOME INSTALLATION  
3. If desired, place the Chameleon Dome over the WDR-D3  
Push the Chameleon Dome over the WDR-D3 until it snaps into  
position.  
Notes : If painting is desired, please do so before installation  
* Painting method on Chameleon Dome  
* Spray the Chameleon Dome with your desired color  
* If necessary apply a second coat  
 
INTERNAL COMPONENTS  
1. Mechanical  
(2) JOY STICK  
(1) DC Auto iris  
2.8~10mm Lens  
(1) DC AUTO-IRIS LENS  
Adjust between TÅÆW (TELE ÅÆ WIDE) to set the  
angle (focal length) Set the focus by adjusting ÅÆN  
NOTE: BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED  
INTO POSITION THROUGH THE USE OF "LOCKING HANDLES".  
(2) JOY STICK  
TO SET THE OSD (ON SCREEN DISPLAY) , PRESS THE JOY  
STICK FOR ONE SECOND AND SET AS DESCRIBED  
IN THE MANUAL  
 
2. Joy Stick  
UP  
RIGHT  
LEFT  
DOWN  
Push the Joy stick for one second, and the OSD appears  
on the screen. Move the Joy Stick up, down, left & right to  
control the OSD functions.  
 
1. GENERAL INFORMATION  
SAFETY PRECAUTION  
Do not open and modify  
Do not open the cabinet except during maintenance and installation, as it may be dangerous and cause damage.  
Do not put objects inside the unit  
Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or  
damages.  
Be careful when handling the unit  
To prevent damage, do not drop the camera or subject it to strong shock or vibration  
Install away from electric or magnetic fields  
Protect from humidity and dust  
Protect from high temperature  
Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels.  
Cleaning  
Dirt can be removed from the cabinet only by wiping it with a soft cloth moistened with a soft detergent solution.  
Mounting Surface  
The mounting surface material must be strong enough to secure the camera.  
2. EXHIBIT  
TIP FOR LOCATION OF THE CAMERA  
Before sending the camera out for repair, check the items below. If the problem persists after checking these  
items, contact your service center.  
If no image appears  
Is the coaxial cable attached securely?  
Are the power and voltage normal?  
Has the iris of the lens inside the camera been adjusted correctly (with the level volume) ?  
Is there adequate illumination?  
If the image is unclear  
Is the lens in focus?  
Is the lens dirty?  
Dirt of fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens  
with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).  
Is the monitor adjusted correctly?  
WARNING:  
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO  
RAIN OR MOISTURE.  
 
3. CAMERA FEATURES  
PRODUCT FEATURE  
1. High Resolution  
It has 540 lines of horizontal resolution and 460 lines of vertical resolution. (540 HTVL equivalent)  
2. Superior Wide Dynamic Image Quality  
It has very Wide Dynamic Range by using Pixim ORCA Chip Set.  
Film-like colors are described under various Light conditions even in high dynamic range scenes  
Dynamic Range is greater then 120 dB.  
3. Digital Pixel System  
Each pixel is processed independently to get clear and usable images.  
4. Various Lens Choices  
it offers flexibility of the lens from board mount to C/CS mount lens with manual and  
DC auto-iris control.  
5. Power Source  
DUAL VOLTAGE (12VDC or 24VAC)  
6. OSD control  
Every function is controlled by OSD menu  
- Automatic white balance  
- Automatic gain control (max 60dB)  
- Slow shutter, AGC on/off  
- Line lock phase control  
- Lens type control  
- Auto exposure control  
7. Synchronization  
Both Internal Synchronization and External Synchronization is provided.  
8. Camera ID  
The title that indicated on Monitor can be appointed.  
9. NTSC/PAL Selectable  
NTSC or PAL is selectable by simple switch is one camera  
 
4. CAMERA SPECIFICATION  
Signal System  
Pick-up Device  
NTSC / PAL  
1/3 inch CMOS (dramatically Dynamic range sensor)  
Total of pixels  
742(H) x 552(V)  
Horizontal Resolution  
Scanning System  
Synchronization  
520 Horizontal TV Lines (color)  
525 Iines interlaced / 625 Iines interlaced  
Internal / External  
1.0Vp-p/75 ohm Composite  
DC Lens, Video Lens, Manual Lens  
0.08Lux (DSS on) with F1.2 Lens  
Video Output  
Iris Control  
Sensitivity  
S/N Ratio  
48dB or more  
Dynamic range  
120dB(max), 95dB(typical)  
1/60 - 1/100,000 / 1/50 - 1/100,000  
C/CS mount  
Shutter Speed  
Lens Mount  
AGC Control  
0 - 60dB  
OSD Menu Control  
Supplied Voltage  
Power Consumption  
Operating Temperature  
Storage Temperature  
Operating Humidity  
Storage Humidity  
4-directional Swith with a center Push TACT Switch  
DC 12V (8V - 18V), AC 24V {(20V - 30V)option}  
Max 2.7W  
-10°C ~ 50°C  
-20°C ~ 70°C  
Under 90% Non-condensing  
under 95% Non-condensing  
 
5. MENU AND SETTING DETAILS  
MAIN MENU  
SET UP ID  
DISPLAY ID:ON or OFF  
CAMERA ID : 8 CHARACTER  
ID POSITION : UP-LEFT or UP-CENTER or UP-RIGHT  
DOWN-LEFT or DOWN-CENTER or DOWN-RIGHT  
RES : CCD-HIGH or CCD-NORMAL  
PIXIM-HIGH or PIXIM-NORMAL  
LENS  
WDR  
MANUAL  
DC : LEVEL (Range 0~255)  
MANUAL(Range -20 to 20)  
AUTO  
WB CONTROL  
ATW(Range 2K~11K)  
AWB  
MANUAL(Range 2K ~11K)  
AGC CONTROL  
LOW LIGHT  
SPECIAL  
OFF  
ON(Range 0 ~ 60)  
SLOW SHUTTER(Range OFF~X32)  
AUTO D/N  
VIDEO(NTSC/PAL)  
FLIP(ON/OFF)  
SYNC(INT/INT2/L,LOCK)  
BACK LIGHT(ON/OFF/BACK LIGHT JONE)  
FLICKER LESS(OFF/ON/FLICKER LESS JONE)  
COLER MODE(B/W,OFF)  
SHARPNESS(Range -8 ~ 8)  
EXIT MENU  
EXIT NO CHANGE  
SAVE NEW AND EXIT  
RESTORE FACTORY SETTING  
RELEASE VERSION  
 
OSD MENU CONTROL  
CENTER KEY - Used to access the menu mode, Also used to confirm the setting  
UP / DOWN KEY - Used to choose the desired menu selection.  
LEFT / RIGHT KEY - Used to choose the desired menu feature adjustment.  
OSD MENU ENTER / EXIT  
A. OSD MENU ENTER  
• Push Center Key for 2 seconds  
B. OSD MENU EXIT  
• Press EXIT Menu from Main Menu  
• If Pressing Set Key for 2 seconds from Main Menu appears.  
In this case, just press Set Key.  
C. 'SAVE' and 'QUIT‘  
• Left or Right Key - Selecting Menu  
• Up or Down Key - Returning to Menu  
1. Press the SET key to access the main setup mode.  
2. Select the desired feature using the UP or Down key.  
3. Change the status of the selected feature using the LEFT or RIGHT key.  
MAIN MENU  
A. SETUP ID  
• DISPLAY ID  
- ON :The ID name will displayed in the monitor.  
- OFF : The name will not displayed in the monitor.  
• CAMERA ID : You can be written to 8 characteristic.  
• ID POSITION : Select on screen position of the camera ID.  
• RES : Select Resolution of CCD or PIXIM  
B. LENS  
• MANUAL : Use When using Manual lens.  
• DC : You can control the brightness of the screen and adjust the desired DC level from 0 to 255.  
C. WDR  
•WDR (Wide Dynamic Range) : You can adjust the desired WDR level from -20 to 20.  
D.FILKER LESS  
•AUTO DECTECTION or SELECT AREA  
 
E. WB CONTROL  
• ATW (Auto Tracking White Balance) : The camera automatically control the white balance in any environment.  
• AWB (Auto White Balance) : The white balance is automatically adjusted in a specific environment.  
• MANUAL : Users can adjust the colors by adding or reducing the WB level.  
You can adjust the desired WB level from 2K to 11K  
F. AGC  
• ON : Activate automatic gain control feature.  
You can adjust the desired AGC level from 0 to 60dB.  
• OFF : Deactivate automatic gain control feature.  
G. LOW LIGHT  
• SLOW SHUTTER : Control Image brightness by adjusting shutter speed  
- AGC : Auto Gain Control setting( Range 28 to 48)  
• AUTO D/N : AUTO DAY/NIGHT  
H. SYNC  
• INTERNAL : Internal synchronization  
• INTERNAL2 : Internal synchronization (Color Rolling Mode)  
• LINE LOCK : Phase adjustment may be necessary in multiple camera installations to prevent picture roll  
when switching between cameras  
I. EXIT MENU  
• EXIT NO CHANGES : No change  
• SAVE NEW AND EXIT : Save change  
• RESTORE FACTORY SETTINGS : Factory default  
• SW REV  
J. VIDEO  
• NTSC or PAL SELECTION  
K. FLIP  
• HORIZONTAL REVERSE  
L. BACK LIGHT  
• BACK LIGHT NONES ADJUST or SELECT AREA  
M. COLOR MODE  
• COLOR or B/W SELECTION  
N. SHARPNESS  
• You can adjust the desired Sharpness level from -8 to 8.  
O. PREVIOUS PAGE  
• PREVIOUS PAGE : Return page  
 
DIMENSIONS  
* SIDE VIEW : WDR-D3  
* TOP VIEW : WDR-D3  
 
WARRANTY  
 
200 New Highway  
Amityville, NY 11701  
631-957-8700  
 

SIIG Computer Hardware 104 0722A User Manual
Sony Camera Lens SAL1635Z User Manual
Sony Car Stereo System CDX GT424U User Manual
Sony Cassette Player 323 User Manual
Sony Laptop PCG FX120K User Manual
Sony Satellite Radio Satellite Radio User Manual
Sony Webcam PCS TL33 User Manual
Stearns Safety Survival Boating Equipment 1189 User Manual
Sunbeam Mixer JM5900 User Manual
Sunrise Medical Mobility Aid 1200 Series User Manual