Silvercrest Bluetooth Headset SBTF 10 A1 User Manual

®
Bluetooth Hands-Free Kit SBTF 10 A1  
GB/IE  
Bluetooth® Hands-Free Kit  
Operating instructions  
KOMPERNASS GMBH  
BURGSTRASSE 21 · D-44867 BOCHUM  
ID-Nr.: SBTF 10 A1-08/10-V2  
 
CONTENT  
PAGE  
Safety instructions  
3
5
6
6
7
7
8
9
Correct Usage  
Introduction  
Items supplied  
Technical data  
Operating Elements  
Installing the hands-free appliance in a vehicle  
Switching the hands-free appliance on and off  
Coupling the hands-free appliance with a mobile  
telephone  
9
Coupling the hands-free appliance with several  
mobile telephones  
11  
11  
12  
Separating the connection  
Re-establishing the connection  
 
1
Using the hands-free appliance  
Troubleshooting  
Cleaning and Care  
Disposal  
12  
14  
15  
15  
16  
17  
Warranty & Service  
Importer  
Information regarding the conformity declaration 18  
 
2
BLUETOOTH® HANDS-FREE KIT  
Safety instructions  
Please read these operating instructions carefully and fold out the page with  
illustrations when you do so. Closely heed this information when operating the  
appliance. Should you have any further questions regarding use, please contact  
the service department responsible for your country. Keep these operating instruc-  
tions in a safe place and pass them on to whomsover might later acquire the  
appliance.  
Traffic safety has priority!  
• Comply with all local laws. When driving, your hands must ALWAYS be free  
to operate the vehicle safely. Traffic safety must ALWAYS take priority whilst  
driving.  
• Only manipulate the hands-free appliance on those occasions in which the  
traffic situation permits it and in which you will not endanger, injure, obstruct or  
cause annoyance to other road users.  
• Do not permit your concentration on the road traffic to be compromised by the  
manipulation and displays of the handsfree appliance!  
• Become familiar with the operation of it before driving off and practice the  
safe operation of the facility!  
• Install the hands-free appliance in the vehicle such that your view is not  
obstructed and that the appliance is not located in an impact zone in the  
passenger compartment or in the inflation area of airbags.  
 
3
General safety instructions  
• Do not attempt to open or repair the appliance. Should you do so, appliance  
safety can no longer be assured and the warranty becomes void.  
• Have the defective device repaired by customer service or an authorised  
specialist only. No liability will be accepted for damage caused by misuse,  
improper handling, use of force or unauthorized modification.  
• Never subject the appliance to moisture, extreme temperatures or extreme  
vibrations.  
• Do not allow children and people subject to supervision play with the  
appliance, they could injure themselves or cause damage to the appliance.  
Connection to other mobile telephones  
• If you wish to connect the appliance to another appliance, read the operating  
instructions to obtain detailed safety instructions. Do not connect it to a product  
that is not compatible.  
High frequency signals in vehicles  
HF signals can, under circumstances, negatively influence the function of not  
properly installed or not sufficiently shielded electronic systems in vehicles,  
e.g. electronic ABS, electronic tempo controllers and airbag systems. For further  
information about your vehicle or its possible ancillaries make contact with the  
respective manufacturer or their representative.  
 
4
Correct Usage  
The Bluetooth® Hands-Free Kit SBTF 10 A1 is designed for use in vehicles with a  
voltage of 12-24 V. The handsfree phone system uses both Bluetooth® radio tech-  
nology as well as a digital signal processor (DSP) to carry out telephone functions.  
This device may be used ONLY for private domestic purposes, not for industrial  
or commercial applications. The product at hand is, by default, NOT intended  
for use in medicinal, lifesaving or life support applications. All of the additional  
connecting cables and external devices used MUST match the safety-related,  
electromagnetic compatability and shielding quality standards of the device at  
hand. With regard to CE Conformity, this device fulfills all of the relevant norms  
and guidelines. In the event of modifications being made to the device without  
agreement from the manufacturer, compliance with these norms and guidelines  
can no longer be assured. Use only the accessories specified by the manufactu-  
rer. If you are using the device outside the territory of the Federal Republic of  
Germany you must pay heed to the national regulations resp. the laws of the  
country in which it is being used.  
 
5
Introduction  
Bluetooth® is a wireless communication system with a short range. It makes  
possible wireless connections between Bluetooth® appliances, such as for example  
mobile telephones, PDA and PCs. Bluetooth® relates itself to a worldwide stan-  
dard for operation in the internationally recognised ISM Frequency Range  
(Industrial, Scientific and Medical). Within the ISM Frequency Range  
(2.402 - 2.480 GHz), a data transfer range of ca. 10 Meters (Klasse II) is  
achieved. The disturbance susceptibility through other users of the ISM  
Frequency Range, such as for example microwaves, WLAN (802.116) or  
garage door openers, is minimised by so-called „Frequency-Hopping“.  
With Frequency-Hopping, a change of frequency levels takes place at up to 1600  
times per second, thereby Bluetooth® is also reckoned to be relatively tap-proof.  
The HSP (Headset-Profil) makes possible standard functions such as voice  
transference, as well as the acceptance and rejection of calls.  
The HFP (Handsfree-Profil) makes possible the hands-free call functions of a  
mobile telephone, for example with the help of voice commands.  
Items supplied  
Bluetooth® Hands-Free Kit  
Operating instructions  
 
6
Technical data  
Operational voltage:  
12-24 Volt DC / 500 mA  
Version 2.1 + EDR, 10 Meter range  
Bluetooth® Specification:  
Supported Bluetooth® profiles: HSP and HFP  
Dimensions (L x W x H):  
Weight:  
Operational temperature:  
Storage temperature:  
Humidity:  
15.5 x 5.5 x 3.2 cm  
67 g  
+5° to +40°C  
-10° to +60°C  
5 to 90% (no condensation)  
Operating Elements  
1 Vehicle connector plug  
2 Loudspeaker  
3 Volume control  
4 Multi-function button  
5 Microphone  
6 LED status display  
 
7
Installing the hands-free appliance in a vehicle  
So that the hands-free appliance can function correctly, it is con-nected to the  
vehicle cigar lighter socket and provided with electricity from there.  
• Ensure that the hands-free appliance engages completely and that the  
operation of the vehicle is not negatively influenced. The LED status indicator 6  
blinks every 3 seconds and a short high signal tone sounds once.  
The appliance is in standby mode.  
Note:  
It is possible that the cigar lighter only functions when the vehicle ignition is  
switched on. In cases of doubt, consult the operating instructions for the  
particular vehicle.  
Caution:  
For vehicles in which the cigar lighter, resp. the vehicle circuit plug, also functions  
when the ignition is switched off:  
• Use the hands-free appliance only when the motor is running. Otherwise, the  
vehicle batteries could become discharged over an extended period of time.  
Note:  
When you are not using the hands-free equipment remove it from the vehicles  
cigarette lighter socket. Store it in a dry, dust free location protected from direct  
sunlight.  
 
8
Switching the hands-free appliance on and off  
Switching on: The appliance is switched off.  
• Press and hold the multi-function button 4 for 3 seconds, until a short and  
high signal tone is heard. The LED status display 6 blinks every 3 seconds.  
Switching off: The appliance is in standby mode.  
• Press and hold the multi-function button 4 for 3 seconds, until a long and  
deep signal tone is heard. The LED status display 6 extinguishes.  
Coupling the hands-free appliance with a mobile telephone  
The hands-free appliance has been especially developed for mobile telephones  
that support the Bluetooth® Profile „Handsfree (HFP) and Headset (HSP)“.  
Further information about Bluetooth® radio technology is to be found in the  
operating instructions for your mobile telephone.  
Before you can use the hands-free appliance, you must connect it with a  
compatible mobile telephone (pairing).  
• Check to make sure the mobile telephone is switched on.  
• Programme the mobile telephone so that it searches for Bluetooth® appliances.  
A detailed description of how to do this is to be found in the operating instruc-  
tions for your mobile telephone.  
• Ensure that the hands-free appliance is correctly set up and switched off.  
 
9
• To switch the device off, press and hold the multi-function button 4 for about  
3 seconds. A long, low signal tone will be heard and the LED status display 6  
extinguishes.  
• Position the hands-free appliance and the mobile telephone so that they are  
not more than 1 metre away from each other.  
• Press and hold down the multi-function button 4 for 6 seconds until, after  
3 seconds a short, high signal tone and after a further 3 seconds a succes-  
sion of low and high signal tones are heard. The LED status display 6 lights  
up constantly and the hands-free equipment is now in the coupling mode.  
• Select the hands-free provision „Car Kit“ from the list of available appliances  
for the mobile telephone.  
• Enter in the pre-programmed passcode "9999" and then confirm it, which  
couples the appliances with each other. You will hear a long high signal tone  
and the LED status indicator 6 blinks every 3 seconds.  
• You can now use the hands-free appliance.  
Note:  
If the coupling is not completed within 2 minutes, the hands-free appliance swit-  
ches itself off. The LED status display 6 extinguishes and you will hear a long  
and deep signal tone. With some mobile telephones it is possible that coupling  
does not automatically take place. In this case coupling must be carried out  
additionally on the mobile telephone. The LED status display 6 blinks twice every  
3 seconds until this has been carried out. Further information can be found in  
your mobile telephone’s operating instructions.  
 
10  
Coupling the hands-free appliance with several mobile  
telephones  
You can couple the hands-free appliance with up to eight mobile telephones.  
However, it can only be connected with one mobiletelephone. If a further mobile  
telephone is coupled with the hands-free appliance, the coupling information of  
the first coupled mobile telephone is erased.  
When the hands-free appliance is switched on, within a few seconds it attempts  
to make a connection to the last used mobile phone. Should a connection not be  
possible, the hands-free appliance nonetheless remains recognisable for other  
mobile telephones. To use the hands-free appliance with a linked mobile phone  
that is not the last used mobile phone, the connection must be made via the Blue-  
tooth® menu of the mobile phone.  
Separating the connection  
If you wish separate the mobile telephone from the hands-free appliance, for  
example, to connect it to another Bluetooth® appliance:  
• Switch the hands-free appliance off  
or  
• separate the connection over the Bluetooth® menu in the mobile telephone.  
You need not erase the coupling with the hands-free appliance in the Bluetooth®  
menu to separate the connection.  
 
11  
Re-establishing the connection  
If you want to reconnect the hands-free appliance with the last used mobile phone:  
• Check to see that Bluetooth® is activated in the mobile telephone, then switch  
the hands-free appliance on.  
When connecting to a previously coupled mobile telephone it is not necessary to  
enter a pass-code. You can set your mobile telephone so that when the hands-free  
equipment is switched on a connection with the mobile telephone is automatically  
established. As soon as the hands-free equipment is connected to the previously  
coupled mobile telephone a short, high signal tone is emitted confirming the con-  
nection. Further information regarding automatic coupling can be found in your  
mobile telephone’s operating instructions.  
Using the hands-free appliance  
After successful coupling, the following functions are available to you. Some of  
the described functions are only possible with a mobile telephone that supports  
the Handsfree Profile (HFP).  
Call function  
• Use your mobile telephone in the usual way to make a call.  
• For redialing of the last number called, shortly press the multi-function button 4  
twice.  
• For activation of voice dialling, shortly press the multi-function button 4 once.  
 
12  
Note:  
Voice dialing is only available with mobile telephones that support this function.  
Further information regarding voice dialing is to be found in the operating  
instructions for your mobile telephone.  
Accepting and ending a call  
When you receive a call the LED status display 6 blinks and you hear a call  
tone from the hands-free appliance. If the call signal in your mobile phone is swit-  
ched off, the ringing tone is nonetheless sounded via the hands-free appliance.  
• Press the multi-function button 4 shortly once, to accept the call.  
• Press the multi-function button 4 shortly once, to terminate the accepted call.  
You can also accept and terminate the call over the mobile telephone.  
Automatic call acceptance  
If automatic call acceptance is activated in the mobile telephone, it accepts the  
incoming call after a determined time period and then passes it on to the  
hands-free appliance. Further information regarding automatic call acceptance  
is to be found in the operating instructions for your mobile telephone.  
Rejection of a call  
• Press the multi-function button 4 for 3 seconds to reject an incoming  
telephone call.  
 
13  
Adjusting the volume of the hands-free appliance  
You can adjust the volume of the hands-free appliance with the assistance of the  
volume controller 3.  
• During a call, turn the volume controller 3 until the desired volume level is  
heard.  
Troubleshooting  
If you cannot connect the hands-free appliance with a compatible mobile  
telephone, proceed as follows:  
• Ensure that the Bluetooth® function in the mobile telephone is activated.  
• Ensure that the hands-free appliance is correctly installed, switched on and  
supplied with electricity.  
• If you use several Bluetooth® appliances, ensure that a previously created  
Bluetooth® connection of the mobile telephone is separated.  
• Ensure that the hands-free appliance is distanced a maximum of 10 metres  
from the mobile telephone and that there are no barriers or electronic devices  
between them.  
If these measures do not correct the problem, please contact the appropriate  
service partner for your country.  
 
14  
Cleaning and Care  
Danger of electrocution!  
• Before cleaning, always separate the electricity supply from the appliance!  
• NEVER submerse the appliance in water or other liquids!  
• Do not permit liquids to permeate into the housing!  
• Never open the housing of the appliance! There are no user-serviceable  
elements inside.  
• Do not use strong detergents, solvents or abrasive cleaning agents to clean  
the appliance. These could damage the housing surfaces.  
• Clean the housing surfaces with a slightly moist soft cloth.  
Disposal  
Do not dispose of the appliance in your normal domestic waste.  
This product is subject to the European guideline 2002/96/EC.  
Dispose of the appliance through an approved dis-posal centre or at your com-  
munity waste facility. Observe the currently applicable regulations.  
In case of doubt, please contact your waste disposal centre.  
Dispose of all packaging materials in an environmentally responsible  
manner.  
 
15  
Warranty & Service  
The warranty for this appliance is for 3 years from the date of purchase. The  
appliance has been manufactured with care and meticulously examined before  
delivery. Please retain your receipt as proof of purchase. In the event of a warranty  
claim, please make contact by telephone with our Service Department. Only in  
this way can a post-free despatch for your goods be assured.  
The warranty covers only claims for material and manufacturing defects, but not  
for transport damage, for wearing parts or for damage to fragile components,  
e.g. buttons or batteries. This product is for private use only and is not intended  
for commercial use. The warranty is void in the case of abusive and improper  
handling, use of force and internal tampering not carried out by our authorized  
service branch. Your statutory rights are not restricted in any way by this warranty.  
The warranty period will not be extended by repairs made under warranty. This  
applies also to replaced and repaired parts. Any damage and defects extant on  
purchase must be reported immediately after unpacking the appliance, at the  
latest, two days after the purchase date. Repairs made after the expiration of the  
warranty period are subject to payment.  
DES UK LTD  
Tel.: 0871 5000 700 (£ 0.10 / minute)  
Kompernass Service Ireland  
Tel.: 1850 930 412 (0,082 EUR/Min.)  
Standard call rates apply. Mobile operators may vary.  
 
16  
Importer  
KOMPERNASS GMBH  
BURGSTRASSE 21  
44867 BOCHUM, GERMANY  
 
17  
Information regarding the conformity declaration  
We, Kompernaß GmbH, declare that the product SBTF 10 A1 Bluetooth® Hands-  
Free Kit conforms to the basic requirements and other relevant provisions of the  
vehicle directive 2004/104/EC and the R&TTE directive 99/5/EC of the  
European Union council.  
The complete Conformity Declaration can be viewed at the Importers premises.  
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.  
The content of this document is presented as it currently exists. Kompernaß GmbH  
does not accept, neither emphatically nor tacitly, any guarantee for the correctness  
or completeness of the content of this document. Kompernaß GmbH retains for  
itself the right, at any time and without previous notice, to make amendments to  
this document or to withdraw it completely.  
 
18  

Sennheiser Microphone 03736 User Manual
Sharp Air Cleaner FU Z31E User Manual
Sharp All in One Printer TINSE2026QSZZ User Manual
Sony Blu ray Player BDP BX310 User Manual
Sony Car Stereo System CDX M620 User Manual
Sony Cassette Player WM FX522 FX521 User Manual
Sony Headphones MDR 7550 User Manual
Sony Speaker System SRS M50 User Manual
Sony Turntable PMPK DJ9000 User Manual
TAG Laptop MIL BOOK 200 Series User Manual