Shure Microphone A98KCS User Manual

Model A98KCS User Guide  
Horn Mount for SM98 or WM98 Microphone  
3. Insert the SM98 or WM98 microphone in the shock mount  
holder by slipping the cable through the slot and sliding the  
connector back through the opening until the protruding black  
cable lock button is in the open slot and the back of the micro-  
phone itself stops flush with the front of the holder. Only the sil-  
ver metal segment of the connector is held by the holder. See  
Figure 3.  
GENERAL  
The Model A98KCS Horn Mount is a versatile device that securely  
attaches Shure SM98 or WM98 microphones to a horn, wind, or  
reed instrument in the exact position desired while protecting the  
instrument and its finish. The cushioned grip is manually tightened  
and securely clamps the rim of the horn. Non-marking neoprene  
rubber on the grip prevents marring the bell or its rim.  
A short gooseneck (165 mm [6-1/2 in.]) attached to the clamp ter-  
minates in a shock-mount adapter for the SM98 or WM98 micro-  
phone. The gooseneck length can be adjusted to facilitate locating  
the microphone in precisely the desired position in the bell of a  
horn. A side screw locks the gooseneck in the chosen position.  
MOUNTING  
1. Attach the cushioned grip to the desired location on the bell of  
the instrument and tighten the knurled top thumbscrew to hold  
the clamp in place. See Figure 1.  
INSERT SM98 IN HOLDER  
FIGURE 3  
4. Slip the cable through the slot in the cable guide (see Figure 4)  
and route the cable away from the horn to prevent transmission  
KNURLED  
TOP SCREW  
of noise and vibration through the cable  
.
ATTACH CLAMP TO HORN  
FIGURE 1  
RETAIN CABLE IN GUIDE  
2. Loosen the knurled side screw on the A98KCS and adjust the  
length of the gooseneck intheclamp. Tightenthescrew.  
SeeFigure 2.  
FIGURE 4  
5. Select the desired location of the microphone by bending the  
gooseneck as required. If necessary re-adjust the gooseneck  
length as described in step 2.  
6. To prevent wind noise, use the windscreen supplied with the  
microphone.  
SIDE SCREW  
USE SIDE SCREW TO ADJUST LENGTH OF GOOSENECK  
FIGURE 2  
NOTE: A supplied optional 1/16-inch setscrew and hex wrench can  
be used to replace the side screw when repeated adjustments of  
the gooseneck length are not required.  
SHURE Incorporated http://www.shure.com  
United States, Canada, Latin America, Caribbean:  
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.  
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446  
Europe, Middle East, Africa:  
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414  
Asia, Pacific:  
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055  
©2005, Shure Incorporated  
27B2580 (Rev. 5)  
Printed in U.S.A.  
 

Solo USA Radar Detector R D 5 1 1 0 User Manual
Sony Laptop PCG 8491 User Manual
Sony Network Card PCLK MN10A User Manual
Sony Projection Television KDF 60XBR950 User Manual
Sony Universal Remote RM LP204M User Manual
Spirit Treadmill Z88 User Manual
Stanton DJ Equipment SCS4DJ User Manual
Star Micronics TV Converter Box SPC 8K User Manual
Sunbeam Blender PB9500 User Manual
Sunbeam Blood Pressure Monitor 7689 User Manual