Shure Car Stereo System UA864 User Manual

Wireless Accessory  
UA864  
User Guide  
Le Guide de l’Utilisateur  
Bedienungsanleitung  
Manuale d’uso  
Guia del Usuario  
Guida dell’Utente  
Gebruikershandleiding  
Руководство пользователя  
Pengguna Panduan  
取扱説明書  
사용자 안내서  
用户指南  
© 2013 Shure Incorporated  
Printed in U.S.A  
27A20829 (Rev. 3)  
*27A20829*  
 
Installation  
Mounting on a Wall or Ceiling  
The mounting plate installs directly to a wall, ceiling, or a standard junction box.  
Required Equipment  
Installation Steps  
• #8 or #6 screws  
• Flat washers  
• Lock washers  
• Drill  
1. Align the mounting plate:  
Junction box mounting: Align the mounting plate with the junction box so that at least two screws can be used.  
Wall mounting: Use the mounting plate as a template to mark the location for the holes on the mounting surface. Drill  
the holes accordingly.  
• Screwdriver  
2. Secure the mounting plate to the surface with the washers as shown (CAUTION: Do not over-tighten screws).  
3. If running RF cable from inside the wall, guide it through the opening in the mounting plate and connect the cable to  
the antenna output.  
4. Position the antenna mounting posts over the keyhole slots in the mounting plate and slide it into the locked position.  
Mounting to an electrical junction box  
Mounting to a wall or ceiling  
Securing the antenna to the mounting plate  
Flat washer  
Lock washer  
Mounting post  
Keyhole slot  
Routing the Cable  
Rotating the Cover  
The output connector can be routed through ports 1 or 2 on the  
antenna. When connecting to an RF cable in the wall, run the  
cable through the opening in the mounting plate.  
The cover can be detached and rotated in any direction for a matched appear-  
ance when using multiple antennas.  
1. Remove the screws holding the cover in place from the back of the antenna  
2. Remove the cover and rotate to the desired position  
3. Replace the screws to secure the cover  
1
Painting the Antenna  
The cover of the antenna can be painted to match the installation environ-  
ment. Use the following guidelines when painting the antenna cover:  
2
• Remove the antenna cover before painting  
• Only use non-metallic paint, as any metallic content may interfere with  
RF reception  
• Allow the paint to dry completely before reinstalling the cover  
• Avoid painting in the screw holes  
Warning: Do not touch the internal components of the antenna when the cover is removed.  
4
 
Connecting to a Receiver  
This antenna is compatible with any receivers, distribution systems, and splitters that operate within the antenna's frequency range. For receivers with  
multiple antenna ports, connect each antenna being used to a separate port.  
Note: The antenna requires bias voltage from the receiver or distribution system to operate on the +10 dB setting and for LED functionality. If these devices do not supply bias voltage, the Shure UABIAST  
inline power supply can be used. The antenna still operates with all other gain settings if bias voltage is not supplied.  
Setting the Gain Switch  
Use the gain switch to optimize antenna performance for the RF characteristics of the room or location. Monitor the RF signal from the receiver to ensure  
optimal signal strength.  
RF Gain Setting (dB)  
Use Scenario  
Pad: −10, −20  
Provides increased isolation from other RF sources when the desired wireless microphone signal strength is strong. If  
the RFOVERLOAD LED illuminates when using a higher gain setting, the pad should be used to attenuate the signal,  
but only after verifying that the transmitter is an appropriate distance from the antenna.  
0 (Default)  
Suitable for typical room installations and provides enough RF gain in most cases when cable runs are between 10 and  
50 feet.  
Boost: +10  
Provides an extra 10 dB of RF gain to compensate for signal loss if using long cable runs (50 feet or more).  
Note: Bias power supplied by receiver antenna ports or an external power source is required for the +10 dB boost setting and for illuminating the LEDs. For un-powered applications, the -20, -10, and 0 dB  
settings are still functional; however, the LEDs will not illuminate.  
Cable Maintenance  
To maintain top performance for UA825, UA850 or UA8100 antenna cables:  
• Avoid sharp bends or kinks in the cables.  
• Do not deform cables with makeshift clamps, such as bending a nail over the cable.  
• Do not use in permanent outdoor installations.  
• Do not expose to extreme moisture.  
5
 
Specifications  
Antenna Cables from Shure  
Shure offers the following pre-terminated antenna cables:  
Connector Type  
BNC, Female  
Length  
Type  
Model No.  
Impedance  
50 Ω  
6 foot  
10 foot  
25 foot  
50 foot  
100 foot  
RG58  
RG58  
UA806  
PA725  
UA825  
UA850  
UA8100  
Power Requirements[1]  
10 to 15 V DC bias from coaxial connection, 75 mA  
RG8X  
RG8X  
RG213  
RF Frequency Range  
UA864US  
UA864LO  
UA864HI  
UA864A  
470–698 MHz  
470–698 MHz  
530–790 MHz  
650–952 MHz  
Certifications  
Reception Pattern  
3 dB Beam Width at center frequency  
This product meets the Essential Requirements of all relevant European  
directives and is eligible for CE marking.  
UA864US  
UA864LO  
UA864HI  
UA864A  
100 degrees  
100 degrees  
95 degrees  
90 degrees  
europe/compliance  
Authorized European representative:  
Shure Europe GmbH  
Headquarters Europe, Middle East & Africa  
Department: EMEA Approval  
Jakob-Dieffenbacher-Str. 12  
75031 Eppingen, Germany  
Phone: 49-7262-92 49 0  
Third-order Overload Intercept Point (OIP3)  
>30 dBm  
Antenna Gain  
On Axis, 0 dB Gain Setting at center frequency  
UA864US  
UA864LO  
UA864HI  
UA864A  
2.5 dBi  
2.5 dBi  
3.0 dBi  
5.5 dBi  
Fax: 49-7262-92 49 11 4  
Signal Gain  
±1 dB, Switchable  
+10 dB  
0 dB  
−10 dB  
−20 dB  
RF Overload LED Threshold  
−15 dBm  
Dimensions  
176 x 176 x 51 mm (H x W x D)  
Weight  
487 g (17.2 oz.)  
Operating Temperature Range  
−7°C (20°F) to 49°C (120°F)  
Storage Temperature Range  
−29°C (-20°F) to 74°C (165°F)  
[1]−20, −10, 0 dB settings do not require power  
6
 
Side View  
Top View  
90˚  
0˚  
60˚  
5 dB  
30˚  
30˚  
0 dB  
30˚  
60˚  
60˚  
-5 dB  
-10 dB  
UA864US/  
-15 dB  
-10 dB -5 dB  
0 dB  
5 dB  
90˚  
90˚  
0˚  
UA864LO  
-15 dB  
585 MHz  
30˚  
60˚  
90˚  
0˚  
90˚  
5 dB  
30˚  
30˚  
60˚  
0 dB  
60˚  
60˚  
30˚  
-5 dB  
-10 dB  
90˚  
90˚  
UA864HI  
-15 dB  
-10 dB -5 dB  
0 dB  
5 dB  
0˚  
-15 dB  
700 MHz  
30˚  
60˚  
90˚  
0˚  
90˚  
5 dB  
30˚  
30˚  
60˚  
0 dB  
60˚  
60˚  
30˚  
-5 dB  
-10 dB  
90˚  
90˚  
UA864A  
-15 dB  
-10 dB -5 dB  
0 dB  
5 dB  
0˚  
-15 dB  
790 MHz  
30˚  
60˚  
90˚  
 
Europe, Middle East, Africa:  
Shure Europe GmbH  
Jakob-Dieffenbacher-Str. 12,  
75031 Eppingen, Germany  
Phone: 49-7262-92490  
Fax: 49-7262-9249114  
PT. GOSHEN SWARA INDONESIA  
Kompleks Harco Mangga Dua Blok L No. 35 Jakarta Pusat  
I.16.GSI31.00501.0211  
 

Sharp Flat Panel Television LC 45GD4U User Manual
Sharp Personal Computer MX 2010U User Manual
Silvercrest DVD Player SHDP 51 A1 User Manual
Singer Sewing Machine 107W15 User Manual
Sony DVD Player BDP S780 User Manual
Sony Speaker System DSR 40 40P User Manual
Sony Stereo System Z L30 User Manual
Sub Zero Refrigerator ICBBI 30UG User Manual
Sylvania TV DVD Combo 6520FDF User Manual
TANDBERG Home Theater Server 116347 User Manual